Type | Standard models | 2-channel models | |
---|---|---|---|
NPN output | E3X-ZV11 | E3X-MZV11 | |
PNP output | E3X-ZV41 | E3X-MZV41 | |
Connecting method | Pre-wired | ||
Outputs | 1 output | 2 outputs | |
Light source (wavelength) | Red, 4-element LED (625 nm) | ||
Power supply voltage | 12 to 24 VDC ±10%, ripple (p-p) 10% max. | ||
Power consumption | Normal mode: 720 mW max.
(Power supply voltage 24 V: Current consumption 30 mA max. / Power supply voltage 12 V: Current consumption 60 mA max.) Eco function ON: 530 mW max. (Power supply voltage 24 V: Current consumption 22 mA max. / Power supply voltage 12 V: Current consumption 44 mA max.) |
Normal mode: 820 mW max.
(Power supply voltage 24 V: Current consumption 35 mA max. / Power supply voltage 12 V: Current consumption 69 mA max.) Eco function ON: 600 mW max. (Power supply voltage 24 V: Current consumption 25 mA max. / Power supply voltage 12 V: Current consumption 50 mA m |
|
Control output | Load power supply voltage: 26.4 VDC, open collector output type
(NPN or PNP output differs depending on the type.) Load current: 100 mA max. (Residual voltage: Load current less than 10 mA: 1V max., load current 10 to 100 mA: 2V max.) OFF current: 0.1 mA max. |
||
Indicators | 7-segment displays
(Threshold Level display: green, Incident Light Level display: red) Display direction: Switchable between normal and reversed. Smart Tuning Indicator (green) Standard models only: OUT indicator (orange) 2-channel models only: OUT1/2 indicator (orange), CH Indicator (green) |
||
Protection circuits | Power supply reverse polarity protection, output short-circuit protection
and output reverse polarity protection |
||
Response
time |
Super-highspeed
mode (SHS) |
Operate or reset: 50 μs | Operate or reset: 100 μs |
High-speed
mode (HS) |
Operate or reset: 250 μs *1 | Operate or reset: 250 μs *2 | |
Standard
mode (Stnd) |
Operate or reset: 1 ms *3 | Operate or reset: 1 ms *4 | |
Giga-power
mode (GIGA) |
Operate or reset: 16 ms | Operate or reset: 16 ms | |
Sensitivity adjustment | Smart Tuning (2-point tuning, power tuning, percentage tuning
(-99% to 99%), maximum sensitivity tuning, full auto tuning, position tuning) or manual adjustment |
||
Mutual interference prevention function | Emission cycle setting switching type
(up to 4 units) |
Up to 2 units for E3X-MZV.
Or, up to 2 units for E3X-ZV (the Unit Number Priority Mode), and 1 unit for E3X-MZV. |
|
Functions | DPC (Dynamic
Power Control) |
Yes | |
ATC (Active
Threshold Control) |
Yes | ||
Timer | Select from timer disabled, OFF-delay,
ON-delay or one-shot timer: 1 to 9,999 ms |
||
Zero reset | Negative values can be displayed. (Threshold value is shifted.) | ||
Resetting settings | Select from initial reset (factory defaults) or user reset (saved settings). | ||
Eco mode | Select from OFF (digital display lit) and Eco ON (digital display not lit). | ||
Power tuning | Select from ON or OFF. | ||
Ambient illumination
(Receiver side) |
Incandescent lamp: 20,000 lx max., Sunlight: 30,000 lx max. | ||
Ambient temperature range | Operating: -25°C to 55°C
Storage: -30°C to 70°C (with no icing or condensation) |
||
Ambient humidity range | Operating and storage:
35 to 85% (with no condensation) within the surrounding air temperature range shown above |
||
Insulation resistance | 20 MΩ min. (at 500 VDC) | ||
Dielectric strength | 1,000 VAC at 50/60 Hz for 1 min | ||
Vibration resistance
(destruction) |
10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y,
and Z directions |
||
Shock resistance (destruction) | 500 m/s2 for 3 times each in X, Y, and Z directions | ||
Weight
(packed state/Sensor only) |
Approx. 95 g/approx. 65 g | Approx. 100 g/approx. 75 g | |
Materials | Case | Polycarbonate (PC) | |
Cover | Polycarbonate (PC) | ||
Cable | PVC | ||
Accessories | Instruction manual, Compliance sheet |